![]() I DID check at the command prompt that my computer had been assigned the reserved WIRED IP address that I had set for this computer. Just to clarify for you – I do have a DHCP setup in my Network, all I have done is “reserved” a couple of IP’s for specific machines on the network. run > cmd > ipconfig /renew > This should tell your computer to request a IP address to your routerĪPIPA * Automatic Private IP Addressing* It’s Job is to give you an IP Address if DHCP is either out of IP Address to assign or Is down or is not installed/configured Then Click On Global Rules Tab > Do The Same "Allow System To Send Requests If The Target Is In "Īllow System To Receive Requests If The Sender Is In You Could Simply Go To CIS > Firewall > Network Security Policy > System > Remove ![]() If I allowed it in the past and wanted to "Disable" the ability of other computers from connecting to this computer on that network, how would I do that? If you wanted to mark it trusted? CIS > Firewall > Stealth Port Wizard > Define a new trusted network > Enter Details > Ok You can go to CIS > Firewall > Network Security Policy > Network Zones tab > See If It’s Here (If not Add > New Network Zone > Name it > Select It > Add > New Address (Enter the address (If you have forgotten > Start > Run > Cmd > ipconfig) If I wanted to add that option in the future how would I enable that? How do I get Comodo to "Detect" the network again so it could be added if I wanted to add it without rebooting in order to get Comodo to "Re-detect" the new network? run > cmd > ipconfig /renew > This should tell your computer to request a IP address to your routerĭHCP Dynamic Host Control Protocol It’s Job is to give out IP AddressĪPIPA * Automatic Private IP Addressing* It’s Job is to give you an IP Address if DHCP is either out of IP Address to assign or Is down or is not installed/configured 2nd question: If I just close the box, and don't add the network, I can't get onto the internet. I am trying very hard to follow it, hopefully someone can shed some light on the subject.ġ69.254.197.119 / 255.255.0.0 asking the usual questions. The granular control is pretty amazing, but the potential to leave a very big hole in your firewall is certainly there with the complexity. ![]() If I allowed it in the past and wanted to “Disable” the ability of other computers from connecting to this computer on that network, how would I do that? If I wanted to add that option in the future how would I enable that? I added the Network Manually so I am assuming that 'no other computers will be allowed to connect to this computer – it was an option that was offered when the new network was “Automatically” detected. When things like this happen it presents a huge potential security risk to “Just allow or Add the Network” without understanding what I just allowed. I Comodo is quite granular in the control it gives you (which can be good and bad), and I don’t consider myself to be an expert at all when it comes to networking, but at the same time I think that I have a pretty good understanding of it. How do I get Comodo to “Detect” the network again so it could be added if I wanted to add it without rebooting in order to get Comodo to “Re-detect” the new network? What is it? The router is taking care of connecting me to my ISP provider - Comodo shouldn’t be seeing ANYTHING like this outside the router - should it?HuhĢnd question: If I just close the box, and don’t add the network, I can’t get onto the internet. This is very strange to me as it has never asked for this before. When I turned off the wireless and plugged in the Ethernet cable Comodo said that there was a New Network detected!?!ġ69.254.197.119 / 255.255.0.0 asking the usual questions. I usually connect to my Router Wirelessly, but about once a week I do a backup to my NAS through a wired Connection because it is faster.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |